Tag Archives: RV

Track Truck – repairs done, now the mods start.

With the required repairs to make it run complete, now the work on mods to get it from a former runner of illegal immigrants, to functional (if not nice) micro toy-hauler can begin.

Flooring

After doing some research at the San Jose International Car Show, I’m now more convinced the flooring found in the van is a factory original. As such, I’ve decided to re-use it.
Sprinter_Project_024
Next to the flooring are two rolls of recycled industrial No-VOC carpets (6’x9′) that are enough to carpet the floor of the van, probably all the way to the firewall if I decided to go that far with it.

Audio / Communications

Having used the existing stereo briefly, I quickly found it’s navigation horribly complicated and it’s general performance underwhelming. Plus, it has a CD player in it.. might as well have an 8-track too. So that was removed, and a new (and very INexpensive Kenwood head with built-in Blutooth, and both Apple and Android music interface capabilities.
Sprinter_Project_025

Having found the unit jammed in there fairly tightly, I ended up going a little medieval on the dash:
Sprinter_Project_026

Having pulled all these parts off ended up making it MUCH simpler to route the Blutooth microphone (required for drivers making phone calls here in Nanny-State Kalifornica). I also noticed that the framework under the dash was painted a bright yellow, not at all like the read the rest of the van is painted.
Sprinter_Project_027

Instructions for mounting the microphone were not at all clear, in fact there was only a single small diagram showing it mounted on top of the steering column. Huh? Screw that I said.. and ripped the left side A pillar cover off and mounted the microphone up at the top of the window, pointing at the driver. I hope that was not a big mistake. I’m sure I’ll test this soon and find out!
Sprinter_Project_029

Running wires down the A-pillar and through the dash was easy enough, but getting from the lower section of the dash up to the top was not exactly obvious. Using a tool not at all designed for the job, often makes things simpler. 🙂 Here I used it to fish the microphone wire up and over the pedal box and long another wire loom, eventually appearing under the HVAC environmental controls.
Sprinter_Project_028

One there, the wrong tool was once again used to fish the wire up to the top section of the dash (removing the cover around the dash vents makes like a lot easier). Viola… easy as cake.
Sprinter_Project_030

Not being a fan of rattles, and especially in the dash area, the wire loom was tightly bundled, and once inserted into the dash, the head unit’s rear section was zip-tied to the dash structure as seen. Probably should have used grey or black wraps but…. I’m going to call this a design test.. yeah, that’s the ticket.. This radio is much tighter in the dash that the other install, and that’s OK by me.
Sprinter_Project_031

Decal Removal

This is nearly complete. There are patches of left over adhesive I need to remove, but the nasty and ugly decals (save a couple that I just might leave) are GONE!! Thank you Magic Eraser!!
Sprinter_Project_032

Sprinter_Project_033

Sprinter_Project_034

Sprinter_Project_035

Sprinter_Project_036

More Interior Cleanup

With some help from the family, we removed A LOT of USPS shipping tape stuck to the ceiling of the truck. Purpose? WHO KNOWS!??! but it was all over the place and Debby just couldn’t stand it.
Sprinter_Project_037

So while she was busy peeling the tape, A.J. and I unscrewed all of the interior panels and removed them from the van. Once able to inspect the the bodywork from the inside, I’m even more convinced that a diamond in the rough is what I have here. No signs of rust or any type of body work / repairs. If it wasn’t so loud, I’d be tempted to just leave the interior just like this!
Sprinter_Project_038

iPhone Integration

One of the features of the head unit, is iPhone (and Android) integration. This I wanted to test out. Thankfully it just worked. One press of the button to change input to USB, about 60 seconds to sync with the phone and store it’s ID, and bang.. music starts playing.

Here I have WAZE up and running on the screen while the music app drops the bass.
Sprinter_Project_039

That was enough for one day… many more days of work on this to come.